Here is what you can do if your Still electric forklift indicates an error.
The following information refers to the models
- RX60-25
- RX60-30
- RX60-35
- RX 60-60
- RX 60-70
- RX 60-80 and
- RX 60-80/900.
The exact model designation of your Still forklift can be found on the factory plate, which is located on the outside right below the front panel.
Attention! Switch off the engine immediately if the display of your Still forklift truck shows an error code. Operate the emergency stop switch in case of acute danger.
Caution! The emergency stop switch overrides the electronic brake. Immediately apply the service brake.
List of Error Codes
We recommend using the search function of your browser to find your error code in the table of diagnostic codes.
| Component Part | Code | Meaning | Possible Solution |
| Temperature Rise | A5022 | Traction motor is too hot | 1. Reduce acceleration and speed 2. If the error occurs more frequently: contact the service |
| Temperature Rise | A5364 | Pump inverter is too hot | Contact the service |
| Accelerator | A3002 A3003 A3004 A3005 A3006 A3007 A3505 | Sensor error: truck does not move | Contact the service |
| Accelerator | A3008 | Throttle voltages (on dual pedal) mismatch: truck will not move | Contact the service |
| Accelerator | A3811 | Throttle configuration is invalid: truck will not move | Contact the service |
| Brake | A3016 A3017 | Sensor error: Truck only drives at emergency operating speed | Contact the service |
| Configuration | A2111 A3801 A3812 | Parameterization error: Traction and hydraulic drive do not work | Contact the service |
| Seat Switch | A302 | Seat switch has not been operated for approximately 8 hours: Truck may be traveling at reduced speed and reduced lifting capacity | 1. Stand up briefly and sit down again 2. If the error persists: contact the service |
| Steering | A3215 A3216 A3570 | Sensor error: Truck is driving at limited speed | Contact the service |
| Driving Direction | A3020 | Switch error: Traction drive does not work or only works to a limited extent | Contact the service |
| Lifting | A3102 A3103 | Sensor error: hydraulics not working or only to a limited extent | Contact the service |
| Tilt | A3107 A3108 | Sensor error: hydraulics not working or only to a limited extent | Contact the service |
| Mast vertical | A3130 A3131 A3132 | Hydraulics not working | 1. Switch off “lift mast vertical position” (see pp. 96 of the operating instructions) 2. Contact the service |
| Vertical Mast Error | A3135 | Hydraulics not working | 1. Switch off “lift mast vertical position” (see pp. 96 of the operating instructions) 2. Contact the service |
| Addition1 | A3112 A3113 | Sensor error: hydraulics not working or only to a limited extent | Contact the service |
| Addition2 | A3117 A3118 | Sensor error: hydraulics not working or only to a limited extent | Contact the service |
| Maintenance | A2242 | Short circuit in encoder supply: truck does not move | Contact the service |
| Monitoring | A2801 A2802 A2808 A2809 A2810 A2815 | Traction drive does not work | 1. Release accelerator pedal 2. If this error occurs sporadically, it can be tolerated. If the operational capability is impaired, then contact service |
| Monitoring | A2803 A2806 | Driving direction is set to neutral | 1. Select a new direction of travel 2. If this error occurs sporadically, it can be tolerated. If the operational capability is impaired, then contact service |
| Monitoring | A2817 | Forklift not ready to drive | 1. Set the key switch to the zero position and restart the truck 2. If this error occurs sporadically, it can be tolerated. If the operational capability is impaired, then contact service |
| Monitoring | A2804 A2805 A2807 A2811 A2812 A2813 A2814 A2816 A2818 | Traction drive does not work or only works to a limited extent | Contact the service |
| Monitoring | A2295 | Traction and hydraulic drives do not work or only work to a limited extent | Contact the service |
| Power Unit | A5031 A5041 A5046 A5301 A5331 A5361 | Temperature sensor error | |
| Battery | A5910 | Hydraulic battery drive support roller not extended | Contact the service |
| Battery | A5920 | Battery drive hydraulic pump overheated | Contact the service |
| Battery | A5930 | key error | Contact the service |
| Battery | A5931 | Plausibility error when extracting the hydraulic battery (affects the potentiometer) | Contact the service |
| Controller | A3305 | CIO doesn’t work | Contact the service |
| Parking Brake Oil Pressure | A3043 | Parking brake oil pressure low: Traction drive locked | Contact the service |
| Parking Brake Oil Pressure | A3049 | Parking brake oil pressure low: truck only drives at emergency limited speed | Contact the service |
| Lifting Lever | A4601 | “Lift” control held too long: “Lift” hydraulics are disabled | Release the lever |
| Tilting Lever | A4602 | Tilt control held too long: Tilt hydraulics are disabled | Release the lever |
| Lever Addition1 | A4603 | “Auxiliary hydraulics 1” control was held too long: Relevant hydraulics are deactivated | Release the lever |
| Lever Addition2 | A4604 | “Auxiliary hydraulics 2” control was held too long: Relevant hydraulics are deactivated | Release the lever |
| Lever | A4680 | Implausible pressure request to the hydraulic pump | 1. Set the key switch to the zero position and restart the truck 2. Contact the service if the error message persists |
Note: The error codes in your specific forklift may differ from those shown here. If in doubt, refer to the user manual.
Contact the Still Service
For questions and repair requests, contact Still Service. If you have not concluded a service contract, we recommend contacting them by phone to receive a direct answer. In principle, an inquiry via the contact form is also possible. You can contact your regional service partner alternatively.
In addition to the exact machine designation, please also have the machine number ready for your inquiry. You will find both on the nameplate, which is located on the right-hand side below the front panel.
Replace it with an used forklift truck
Repairing your Still forklift is not possible or inefficient? You can find used forklifts in good condition on Machineseeker and TruckScout24. Used commercial vehicles are usually 50 to 70 percent cheaper than new vehicles.